- #Unraid setup shared drive using unassisted devices how to#
- #Unraid setup shared drive using unassisted devices install#
- #Unraid setup shared drive using unassisted devices windows 10#
#Unraid setup shared drive using unassisted devices install#
When you install Docker applications on Unraid, the data information from those containers is saved on the Appdata folder. Appdata Backup/RestoreĪnother handy plugin to set up is the Appdata Backup/Restore. After you install the plugin, refresh the page, and the System buttons would now be available on the right side of the menu bar. Next, we have the System Buttons plugin, a very convenient plugin because it provides shortcuts to stop the array, shutdown, and reboot the Unraid server. You can then click on the Preview icon on the right and view the Preclear report. When the process completes, you will get a notification letting you know the preclear finished. When you start the test, the process can take a long time, and it will vary depending on how big the drive is. You can also select if you want to either skip the pre-read or post-read. You can choose to get a notification at different stages of the test or when the script finishes. You can select the script you want to run, the type of operation, the number of cycles. A pop-up comes up where you can configure the test. To start a Preclear test, click on Start Preclear. So, if you are going to preclear a previously used drive, make sure that you check for any unsaved data. Keep in mind that all data on the drive will be erased when you run a preclear test. When you have any unmounted drives on your Unraid server, the drives will show up in there. So, search for Preclear Disk, install it, and click on the Gear icon to open the settings.
This plugin is super helpful because you can use it to run tests on new drives and find potential issues before adding them to the array. The following plugin to set up, which is a must-have, is Preclear Disk. When issues are found, they will be displayed at the bottom and will provide suggestions for you to get the problem resolved. When you complete the configuration, click on Apply. You can also set it up to send notifications for any errors or warnings. For example, you can set up the plugin to run a background scan every hour, daily, weekly, or monthly. In the settings, there are a few options that you can configure. So, search for the plugin, click on the install button, and when the installation completes, click on the Gear icon to open the settings.
#Unraid setup shared drive using unassisted devices how to#
This plugin can find issues on your server and provide suggestions on how to correct configuration problems or other issues found onUnraid. Fix Common Problems PluginĪlright, the first plugin to install is the CA Fix Common Problems.
So, I will be covering some of them on individual tutorials. Docker applications require a few more steps to configure. We’ll go over a few popular plugins that I think everyone should install after setting up a new Unraid server. When the installation completes, refresh the page, and the Apps tab would now be available on the menu bar.Ĭlick on it, and you now have access to a large list of available plugins and Docker containers that you can easily install on your Unraid server.įor this guide, we’ll concentrate on plugins and not Docker containers. Value Type: REG_DWORD – Number (32 bit, hexadecimal)ĭefault: 0, Set to 1 (Use NTLMv2 session security if negotiated)ĭescription: This parameter specifies the type of authentication to be used.To install the Community Apps plugin, go to the Plugins tab, click on Install plugin, enter the URL below, and then click on Install. HKEY_LOCAL_MACHINE\System\CurrentControlSet\control\LSA
#Unraid setup shared drive using unassisted devices windows 10#
In the case of Windows 10 Home, Local Security Policy does not exist therefore make the change in the registry (use regedit). Then just press OK and close all of the open windows and then try again Double click and change the setting to be “Send LM & NTLM – use NTLMv2 session security if negotiated.” In the Local Security Policy screen on the left navigation tree, expand the “Local Policies –> Security Options” then about 2/3rd’s the way down the list you’ll see a Policy called “Network Security: LAN Manager authentication level”. Now double click and open “Local Security Policy”. To access said setting go to the control panel in Windows 10 (or 7), in Category view click on the text “System and Security”, then click on the text “Administrative Tools”. There is a setting in windows Local Security Policy which is incorrectly set by default for viewing an older communication protocol NAS. Posting it here just in case someone else has a similar issue: Found a solution, well lots of solutions, but nothing worked till I found this.
0 kommentar(er)
